Dental Cure Light Universal Composite Resin/ Ortho Adhesive Bonding/Etch Gel Kit

Description

Introduction
Universal Resin Kits
INDICATIONS FOR USE:
Direct restoration for all class caries.
Restoration of teeth defect and veneer.
Package:
REFILL:
Light Cure Composite: 4g/Syringe*5
Syringe Needles : 5pcs/ box*1
Total Etching Adhesive: 5ml/Bottle*1
Etching Gel: 2.5ml/Syringe*1
Applicators Brushes: 20pcs/box*1
Net weight: 188.4g
COLOR: A1,A2,A3,A3.5,B1
FEATURES & ADVANTAGES:
Unique dispersion technology ensure the filler evenly distributed
Radioopaque and fluoride releasing Optimal polishability and high shade stability.
Excellent handling, not sticky to instrument;
Suitable for most cases of restoration, extensive indication of usage.
INSTRUCTIONS：
(1)Preparation: isolate and prepare tooth.
(2)Cleaning: rinse the preparation with water.
(3)Drying: gently air dry until there is no visible water.Do not allow enamel or dentin to dry for an excessive period of time.
(4)Applying Dentex Self-Etching Light Cure Adhesive (DSA):
dispense 1-2 drops of DSA into a mixing well, apply enough DSA to the entire preparation with a little brush until a shiny surface is achieved and then wait for 10 seconds (DSA should not be applied too much ). Use a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching adhesive, an etching step should be used according to the manufacturer's instruction).
(5)Cure: light cure for 20 seconds at 500±50mW/cm2. Keep the distance to exposure surface less than 4 mm.
(6)Applying Dentex light cure composite (DLC): place selected DLC into cavity preparation following by light cure. According to following table, the curing time is recommended for different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an increment filling is recommended. In general, 1-2 mm increments are placed into cavity preparation from different sides and the restoration is built incrementally. Each increment is light cured for 30 seconds.
(7) Finishing: after light cure, adjust restoration.
(8) Polishing: use polishing strip or disc to polish the surface
WARNING:
Do not use this product for patient who is allergy to methylmethacrylate. Do not use this product with any material contained eugenol.
PRECAUTIONS
Methmethacrylate resins may cause skin sensitization in susceptible persons. In case of contact, wash skin with soap and water. In severe situation, get medical attention.
ATTENTION:
To an exposed pulp, a pulp capping material such as Calcium hydroxide may be used before using this product.
STORAGE:
Store at 25℃ or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use.
DISPOSAL:
After the product is used up, dispose it as normal medical rubbish.
SHELF LIFE: 3 years
Orthodontic Adhesive Kit
Orthodontic Adhesive:
Designed for bonding of metal and ceramic brackets on enamel.
It is of high viscosity and thus prevents bracket drifting and reduces material waste.
As it is light cured extra working time is ensured and therefore accurate bracket placement can be obtained.
INDICATIONS FOR USE: Direct bonding of metal and ceramic brackets
STORAGE: Store at 25℃ or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use.
Packing list:
Enamel Adhesive Primer(Total-Etching) 5ml*1 bottle;
Etching Gel 5ml*1 syringe;
Light Cure Adhesive Paste 4g*3 syringe;
Little brush 20;
Syringe tip:10
No-Mix Adhesive
Feature:
Specifications:
1. This product is one kind of orthodontic direct bonding system resin with aromatic bis dimethyl acrylate resin as its main material.
2. As a new-type orthodontic direct bonding system, it is convenient to use with little waste, easy to handle independently and has a favorable clinical bonding strength.
3. It consists of primer and paste with acid etchant, spatulas and small brusher as its accessories.
Preparation:
Clean tooth enamel surface,eliminate tooth contamination,rinse then isolate tooth and blow-dry.
Etching:
Etching the enamel of the tooth with acid etchant for 50 or 60 sec. Rinse and dry with clean air. If the enamel does not have a chalky appearance, pls. repeat the process;
Brushing:
apply a thin layer of the primer over the etched enamel with the brusher;
Bonding:
apply another thin layer of the paste to seal the edges, adjust the bracket within 20 sec, give pressure for 5 to 10 secand remove the excessive primer and paste after 40 to 60 sec; then do orthodontic procedures followed 5-min curing.
Packaging Detail:
3 x black syringes (3.5g)
1 x primer bottle (10ml)
20 x Brushes
Light Cure Adhesive
Warning: Ortho-Bonding primer and adhesive contains acrylate monomers. Acrylate monomers are known to produce allergic skin reactions in certain sensitive individuals.
May cause eye and skin irritation.
Precautions: A void eye and skin contact. Wear gloves when handing this material.
Precaution:Please follow manufacturer's directions on the handing, proper use and recommendations for eye protection, when using a curing light
This system is designed to be used at room temperature (20-25°C, 68-77°F)。Storage between 2-27°C/35-80°F Light Sensitive
Contents of each box
3 x Adhesive paste Syringes (10.5g)
1 x Primer Bottle (8ml)
40 x Brushes
1 x Instruction Bookle
Mini No-Mix Adhesive
Description:
1. This product is one kind of orthodontic direct bonding system resin with aromatic bis dimethyl acrylate resin as its main material.
2. As a new-type orthodontic direct bonding system, it is convenient to use with little waste, easy to handle independently and has a favorable clinical bonding strength.
3. It consists of primer and paste with acid etchant, spatulas and small brusher as its accessories.
Preparation: Clean tooth enamel surface,eliminate tooth contamination,rinse then isolate tooth and blow-dry.
Etching:Etching the enamel of the tooth with acid etchant for 50 or 60 sec. Rinse and dry with clean air. If the enamel does not have a chalky appearance, pls. repeat the process;
Brushing: apply a thin layer of the primer over the etched enamel with the brusher;
Packaging Detail:
1 x bottle（3ml）Primer
1 x Syringes (3.5g each)Paste
1x Syringes (2.5ml)etchant Gel
7x Brushes
1xSyringe tip
STORAGE: Store at 25℃ or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use.
Orthodontic Adhesive
Feature:
This orthodontic adhesive provides a longer working time and a rapid setting time. Can be placed directly into bands. Excess flash is easy to clean up prior to the light curing and the cement is easy to see due to the blue color.
It contains fluoride to reduce the chance of declacification.
Packing list of one pack
1 x Etchant acid Gel 2.5ml  syringe;
1 xLight Cure Adhesive Paste 5g  syringe;
1 x Syringe tip
Box size: 17*11*2.5cm
A1+A2+A3+A3.5+B1+B2
All Class of direct restoration for anterior and posterior.
Indirect restoration such as Veneer,inlay and onlay.
Core buildups.
Advantages:
Solution of simplicity with universal shade
The shade of DX.Universal Composite matches with VITA classic shade guide. Therefore single shade restoration can be applied as conventional & ordinary solution.
Nano hybrid technology
DX.Universal composite is applying unique nano hybrid dispersion technology to maximize the load of fillers by controlling the size and distribution of particles. It dramatically increased composite physical properties and notably improved the smooth surface of restoration in comparision with traditional micro hybrid or hybrid composite.
High Radiopaque.
Fluoride releasing to prevent recurrent caries.
Excellent handling.
Extensive indications that suitable for most cases of restorations.
Color Available: A1, A2, A3, A3.5,B1,B2
Etching Gel 37%
Dentex etching gel is a polymer thickened gel for use on enamel and dentin.
This gel will effectively treat enamel and dentin, producing the necessary microretentive surface for successful bonding. The polymer thickener creates thixotropic properties, enhancing handling characteristics. The etchant rinse away cleanly and quickly, leaving no residue.
Packages: Refill: 5 ml/syringe, Instruction X1
Indications: Treat dentin and enamel, Treating agent on dental restorative material.
1. Isolate tooth and then prepare the cavity in a conservative manner. clean the entire surface with a slurry of pumice and water.
2. Apply etchant using a tip, a disposable syringe tip, or disposable brush tip. allow etchant to remain in palce for 15 seconds. etching time should be monitored with a stopwatch. begin timing at the end of application.
Option: place etchant enamel first, then proceed to cover dentin, for a slightly longer enamel etching time.
3. Rinse thoroughly (at least 5 seconds) to completely remover all traces of etchant.
4. Remove exces moisture from the tooth and proceed with the application of etching gel, waiting for 10 seconds, then rise thoroughly. then apply adhesive
Dentin Bonding Adhesive
5th generation adhesive for all classes of direct restoration.
Post and core bonding.
Ceramic veneer/crown/inlay and other indirect restoration bondings.
Advantages:
High bonding strength and long lasting durability.
Easy infiltrate to dentin tubules.Reduce the risk of post-operative sensitivity.
Compatible with all light cure restoratives.
Time saving and easy to use.
Usage:
Enamel bonding :30 seconds DX.Etch37 etch on enamel then apply 5th generation adhesive.
Dentin bonding:15 seconds DX.Etch37 etch on dentin then apply 5th generation adhesive.
Package:5ml/Bottle
FDA Statement
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
Seller name:Dentaljoy
City,State:SHENZHEN,China
Telephone number:0755-67530378
Re: K192233
Trade/Device Name: LED Curing Light
Regulation Number: 21 CFR 872.6070
Regulation Name: Ultraviolet Activator for Polymerization
Regulatory Class: Class II
Product Code: EBZ
Dated: December 7, 2019
Received: December 16, 2019
K180463
Trade/Device Name: Apoller Flow Light Cure Flowable Composite
Regulation Number: 21 CFR 872.3690
Regulation Name: Tooth Shade Resin Material
Regulatory Class: Class II
Product Code: EBF